Normen voor de Kleur, Glans en Mechanische Testen
ASTM D1002
Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal)
This test method covers the determination of the apparent shear strengths of adhesives for bonding metals when tested on a standard single-lap-joint specimen and under specified conditions of preparation and test.
ASTM D1654
Voluntary Specification, Performance Requirements and Test Procedures for High Performance Organic Coatings on Aluminum Extrustions and Panels
This specification describes test procedures and performance requirements for high performance organic coatings applied to aluminum extrusions and panels for architectural products.
ASTM D1876
Standard Test Method for Peel Resistance of Adhesives (T-Peel Test)
This test method is primarily intended for determining the relative peel resistance of adhesive bonds between flexible adherents by means of a T-type specimen.
ASTM D2244
Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
This practice covers the calculation, from instrumentally measured color coordinates based on daylight illumination, of color tolerances and small color differences between opaque specimens such as painted panels, plastic plaques, or textile swatches.
ASTM D3164/M
Standard Test Method for Strength Properties of Adhesively Bonded Plastic Lap-Shear Sandwich Joints in Shear by Tension Loading
This standard covers a test method for strength properties of adhesively bonded plastic lap-shear sandwich joints in shear by tension loading.
ASTM D3330
Standard Test Method for Peel Adhesion of Pressure-Sensitive Tape
Standard test method for peel adhesion of pressure-sensitive tape.
ASTM D3528
Standard Test Method for Strength Properties of Double Lap Shear Adhesive Joints by Tension Loading
This test method covers the determination of the tensile shear strengths of adhesives for bonding metals when tested in an essentially peel-free standard specimen that develops adhesive stress distribution representative of that developed in a typical low-peel production-type structural joint.
ASTM D412
Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers - Tension
These test methods cover procedures used to evaluate the tensile (tension) properties of vulcanized thermoset rubbers and thermoplastic elastomers.
ASTM D4214
Standard Test Methods for Evaluating the Degree of Chalking of Exterior Paint Films
These test methods cover the evaluation of the degree of chalking on white or tinted exterior paint films.
ASTM D5034
Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test)
This test method covers the grab and modified grab test procedures for determining the breaking strength and elongation of most textile fabrics.
ASTM D5035
Standard Test Method for Breaking Force and Elongation of Textile Fabrics (Strip Method)
This test method covers raveled strip and cut strip test procedures for determining the breaking force and elongation of most textile fabrics.
ASTM D523
Standard Test Method for Specular Gloss
This test method covers the measurement of the specular gloss of nonmetallic specimens for glossmeter geometries of 60, 20, and 85°.
ASTM D624
Standard Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers
This test method describes procedures for measuring a property of conventional vulcanized rubber and thermoplastic elastomers called tear strength.
ASTM D638
Standard Test Method for Tensile Properties of Plastics
This test method covers the determination of the tensile properties of unreinforced and reinforced plastics in the form of standard dumbbell-shaped test specimens when tested under defined conditions of pretreatment, temperature, humidity, and testing machine speed.
ASTM D660
Standard Test Method for Evaluating Degree of Checking of Exterior Paints
Since checking is not easily recognizable, this test method is intended to provide, through definition and illustrations, a means of evaluating the degree of this film failure.
ASTM D661
Standard Test Method for Evaluating Degree of Cracking of Exterior Paints
This test method covers the evaluation of the degree of cracking of exterior paints by comparison with photographic standards.
ASTM D662
Standard Test Method for Evaluating Degree of Erosion of Exterior Paints
This test method covers the evaluation of the degree of erosion of exterior paints by comparison with photographic standards.
ASTM D6862
Standard Test Method for 90 Degree Peel Resistance of Adhesives
This test method covers the determination of the resistance-to-peel strength of an adhesive bond between one rigid adherend and one flexible adherend when tested at an angle of approximately 90 degrees under specified conditions of preparation and testing.
ASTM D7003
Standard Test Method for Strip Tensile Properties of Reinforced Geomembranes
This test method is used to measure the strip tensile properties of reinforced geomembranes.
ASTM D7004
Standard Test Method for Grab Tensile Properties of Reinforced Geomembranes
This test method is used to measure the grab tensile properties of reinforced geomembranes.
ASTM D7087
Standard Test Method for An Imaging Technique to Measure Rust Creepage at Scribe on Coated Test Panels Subjected to Corrosive Environments
This test method covers the measurement of rust creepage area from a scribe line on painted/coated flat test panels after exposure to corrosive environments.
ASTM D714
Standard Test Method for Evaluating Degree of Blistering of Paints
This test method employs photographic reference standards to evaluate the degree of blistering that may develop when paint systems are subjected to conditions which will cause blistering.
ASTM D751
Standard Test Methods for Coated Fabrics
These test methods cover, but are not limited to, rubber-coated fabrics; that is, tarpaulins, rainwear, and similar products
ASTM D772
Standard Test Method for Evaluating Degree of Flaking (Scaling) of Exterior Paints
This test method covers the evaluation of the degree of flaking (scaling) of exterior paints by comparison with photographic standards.
ASTM D882
Standard Test Method for Tensile Properties of Thin Plastic Sheeting
This test method covers the determination of tensile properties of plastics in the form of thin sheeting and films (less than 1.0 mm (0.04 in.) in thickness).
ISO 527
Plastics - Determination of Tensile Properties
SAE J1523
Metal to Metal Overlap Shear Strength Test for Automotive Type Adhesives, Recommended Practice
This SAE Recommended Practice defines a procedure for determining shear strengths of adhesives.
Looking for a specific test standard? Search entire listing of all standards.
U bent nu ingelogd in uw account. U heeft nu toegang tot alle (
) of (
) documenten. Om toegang tot de (
) documenten te krijgen, vragen wij u om uw apparatuur hier te registereren.
U bent nu ingelogd in uw account. U heeft nu toegang tot alle () of () documenten. Om toegang tot de () documenten te krijgen, vragen wij u om uw apparatuur hier te registereren.