加速实验室测试标准
AAMA 2603
Voluntary Specification, Performance Requirements and Test Procedures For Pigmented Organic Coatings on Aluminum Extrusions and Panels
This specification describes test procedures and performance requirements for pigmented organic coatings applied to aluminum extrusions and panels.
AAMA 2603
铝合金型材和板材上的有机颜料涂层的推荐规格、性能要求和测试程序
本规范描述了用于铝合金型材和板材上的有机颜料涂层的测试程序和性能要求。
AAMA 624
Voluntary Specification, Performance Requirements and Test Procedures for High Performance Organic Coatings on Fiber Reinforced Thermoset Profiles
This specification describes test procedures and performance requirements for high performance, organic, coatings applied to fiber reinforced thermoset profiles for windows, doors and similar products.
AAMA 624
纤维增强热固性型材上的高性能有机涂层的推荐规格、性能要求和测试程序
本规范描述了高性能有机涂料的测试程序和性能要求，这类涂料应用于纤维增强热固性型材（窗、门和类似的产品）。
AATCC TM111
Weather Resistance of Textiles: Exposure to Daylight and Weather
This test method provides a means for determining the weather resistance of textile materials.
AATCC TM111
纺织品的耐候性 暴露于日光和气候
本测试方法提供了测定纺织材料耐候性的途径。
AATCC TM16
Colorfastness to Light
This test method provides the general principles and procedures which are currently in use for determining the colorfastness to light of textile materials.
AATCC TM16
耐光色牢度
本测试方法提供了目前用来测定纺织材料日晒色牢度的一般原则和程序。
AATCC TM169
Weather Resistance of Textiles: Xenon Lamp Exposure
This test method provides the procedure for the exposure of textile materials of all kinds, including coated fabrics and products made thereof, in an artificial weathering apparatus using controlled conditions of test.
AATCC TM169
纺织品的耐候性 氙灯曝露测试
本测试方法提供了各类纺织品材料（包括涂层织物和由其制造的产品）在受控测试条件下用人工老化仪器进行曝露测试的测试程序。
AATCC TM186
Weather Resistance: UV Light and Moisture Exposure
This test method provides a procedure for the exposure of textile materials of all kinds, including coated fabrics and products made thereof, in a laboratory artificial weathering exposure apparatus employing fluorescent UV lamps as a light source and using condensing humidity and/ or water spray for wetting.
AATCC TM186
耐候性 紫外线和潮湿曝露测试
本测试方法提供了各类纺织品材料（包括涂层织物和由其制造的产品）曝露测试的程序。测试采用实验室人工老化曝露装置，用荧光紫外灯管作为光源，使用冷凝加湿和/或喷淋加湿。
ASTM B117
Standard Practice for Operating Salt Spray (Fog) Apparatus
This practice provides a controlled corrosive environment which has been utilized to produce relative corrosion resistance information for specimens of metals and coated metals exposed in a given test chamber.
ASTM B117
盐雾试验箱操作的标准测试方法
本测试方法提供了一个受控的腐蚀性环境，用于在给定的测试箱中产生金属和涂层金属样品的相关耐腐蚀性信息。
ASTM C1257
Standard Test Method for Accelerated Weathering of Solvent-Release-Type Sealants
This test method includes two laboratory accelerated exposure procedures for predicting the effects of ultraviolet or ultraviolet/visible radiation, heat, and moisture on color, chalking, cracking, and adhesion of solvent-release sealants.
ASTM C1257
溶剂释放型密封剂加速老化的标准测试方法
该测试方法包括两个实验室加速暴露测试程序，用于预测紫外线或紫外线/可见光辐射、热量和湿气对溶剂释放型密封剂的颜色、粉化、开裂和附着力的影响。
ASTM C1442
Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus
This practice covers three types of laboratory weathering exposure procedures for evaluating the effect of actinic radiation, heat, and moisture on sealants.
ASTM C1442
使用人工老化设备对密封剂进行测试的方法
本测试方法包括三种实验室加速老化曝露程序，评估太阳光辐射、热和潮湿对密封剂的影响。
ASTM C1501
Standard Test Method for Color Stability of Building Construction Sealants as Determined by Laboratory Accelerated Weathering Procedures
This test method describes laboratory accelerated weathering procedures using either fluorescent ultraviolet or xenon arc test devices for determining the color stability of building construction sealants.
ASTM C1501
实验室加速老化程序评估建筑结构密封剂色牢度的标准测试方法
本测试方法描述了使用荧光紫外线或氙灯测试设备测定建筑结构密封剂色牢度的实验室加速老化程序。
ASTM C1519
Standard Test Method for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures
This test method covers the method for the determination of the durability of a sealant based on its ability to function in cyclic movement maintaining adhesion and cohesion after repeated exposure to laboratory accelerated weathering procedures.
ASTM C1519
实验室加速老化对建筑结构密封剂耐候性评估的标准测试方法
该测试方法是密封剂耐候性的测定方法，是基于在依据实验室加速老化程序反复曝露后，密封剂在循环运动中保持粘连和凝聚的能力来制定的。
ASTM C1589
Standard Practice for Outdoor Weathering of Construction Seals and Sealants
This practice describes outdoor exposure procedures used to determine the weathering durability of building construction, seals and sealants.
ASTM C1589
建筑密封件和密封剂户外老化的标准测试方法
本测试方法描述了用于测定建筑结构密封件和密封剂老化耐候性的户外曝露测试程序。
ASTM C732
Standard Test Method for Aging Effects of Artificial Weathering on Latex Sealants
This test method covers a laboratory procedure for the determination of aging effects of artificial weathering on latex sealants.
ASTM C732
乳胶密封剂人工老化试验效果的标准测试方法
该测试方法规定了测定人工老化乳胶密封剂老化效果的实验室程序。
ASTM C734
Standard Test Method for Low-Temperature Flexibility of Latex Sealants After Artificial Weathering
This test method covers a laboratory procedure for the determination of low-temperature flexibility of latex sealants after 500 h artificial weathering.
ASTM C734
人工老化后乳胶密封剂的低温弹性的标准测试方法
该测试方法规定了人工老化测试500小时后乳胶密封剂低温弹性的实验室程序。
ASTM C793
Standard Test Method for Effects of Laboratory Accelerated Weathering on Elastomeric Joint Sealants
This test method covers a laboratory procedure for determining the effects of accelerated weathering on cured-in-place elastomeric joint sealants (single- and multi-component) for use in building construction.
ASTM C793
弹性接缝密封胶实验室加速老化效果的标准测试方法
该测试方法包括了密封剂耐候性的测定，通过将密封剂经依据实验室加速老化程序反复暴露后，评价其在周期运动中保持粘合力和附着力。
ASTM D1002
Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal)
This test method covers the determination of the apparent shear strengths of adhesives for bonding metals when tested on a standard single-lap-joint specimen and under specified conditions of preparation and test.
ASTM D1002
单搭接接头粘接金属样品表面剪切强度的标准测试方法，该强度通过加载拉伸负荷（金属对金属）而测得
本测试方法规定了用于粘接金属的胶粘剂表面剪切强度的测定。测试时，使用标准单搭接接头样品，并在指定条件下制备与测试。
ASTM D1148
Standard Test Method for Rubber Deterioration-Discoloration from Ultraviolet (UV) and Heat Exposure of Light-Colored Surfaces
This test method covers techniques to evaluate the surface discoloration of white or light-colored vulcanized rubber that may occur when subjected to UV or UV/visible exposure from specified sources under controlled conditions of relative humidity, or moisture, and temperature.
ASTM D1148
橡胶老化的标准测试方法－由紫外线（UV）和热曝露引起的浅色表面的变色
本测试方法规定了白色或浅色硫化橡胶表面变色的评估技术，受到指定来源的紫外线或紫外线/可见光照射，在受控的相对湿度或湿气及温度条件下，就有可能发生变色。
ASTM D1654
Voluntary Specification, Performance Requirements and Test Procedures for High Performance Organic Coatings on Aluminum Extrustions and Panels
This specification describes test procedures and performance requirements for high performance organic coatings applied to aluminum extrusions and panels for architectural products.
ASTM D1654
铝合金型材和板材上的高性能有机涂料的推荐规格、性能要求和测试程序
本规范描述了高性能有机涂料的测试程序和性能要求，这类涂料适用于建筑产品（铝合金型材和板材）。
ASTM D1670
Standard Test Method for Failure End Point in Accelerated and Outdoor Weathering of Bituminous Materials
This test method covers the use of a spark generating apparatus for determination of failure due to cracking of bituminous materials undergoing accelerated or outdoor weathering on electrically conductive backings.
ASTM D1670
沥青材料加速和户外老化失效终点的标准测试方法
该测试方法规定了使用火花发生装置测定在导电底材上经加速或户外老化沥青材料的开裂失效。
ASTM D1735
Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus
This practice covers the basic principles and operating procedures for testing water resistance of coatings in an apparatus similar to that used for salt spray testing.
ASTM D1735
使用水喷淋装置测试涂层耐水性的标准测试方法
本测试方法规定了在类似于用于盐雾测试的仪器中测试涂层耐水性的基本原则和操作程序。
ASTM D1876
Standard Test Method for Peel Resistance of Adhesives (T-Peel Test)
This test method is primarily intended for determining the relative peel resistance of adhesive bonds between flexible adherents by means of a T-type specimen.
ASTM D1876
胶粘剂抗剥离的标准测试方法（T型剥离测试）
本测试方法的主要目的是通过一个T型样品测定柔性胶粘体之间粘接接头的相对抗剥离性。
ASTM D2244
Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
This practice covers the calculation, from instrumentally measured color coordinates based on daylight illumination, of color tolerances and small color differences between opaque specimens such as painted panels, plastic plaques, or textile swatches.
ASTM D2244
计算色差、仪器测量出的颜色差异的标准测试程序
本测试方法规定了基于日光照明的仪器测量出的颜色变化的计算，不透明样品如彩板、塑料斑块或纺织品之间的色差公差和颜色的差异的计算。
ASTM D2247
Standard Practice for Testing Water Resistance of Coatings in 100% Relative Humidity
This practice covers the basic principles and operating procedures for testing water resistance of coatings by exposing coated specimens in an atmosphere maintained at 100% relative humidity so that condensation forms on the test specimens.
ASTM D2247
100％相对湿度下涂料防水性能测试的标准方法标准
本测试方法规定了涂层耐水性测试的基本原则和操作程序，用于曝露测试的涂层样品处于相对湿度100%的环境中，这样测试样品上就会形成冷凝。
ASTM D2565
Standard Practice for Xenon-Arc Exposure of Plastics Intended for Outdoor Applications
This practice covers specific procedures and test conditions that are applicable for xenon-arc exposure of plastics conducted in accordance with Practices G151 and G155.
ASTM D2565
户外用塑料氙灯曝露测试的标准测试方法
本测试方法依照G151和G155测试方法规定塑料氙灯曝露测试的具体程序和测试条件。
ASTM D2803
Standard Guide for Testing Filiform Corrosion Resistance of Organic Coatings on Metal
This guide covers three procedures for determining the susceptibility of organic-coated metal substrates to formation of filiform corrosion.
ASTM D2803
金属上的有机涂料耐丝状腐蚀测试的标准指南
本指南涵盖了测定金属底板上有机涂层丝状腐蚀的三个方法。
ASTM D3164/M
Standard Test Method for Strength Properties of Adhesively Bonded Plastic Lap-Shear Sandwich Joints in Shear by Tension Loading
This standard covers a test method for strength properties of adhesively bonded plastic lap-shear sandwich joints in shear by tension loading.
ASTM D3164/M
通过加载拉伸负荷测量粘接塑料搭接接头剪切强度性能的标准测试方法
本标准规定了通过加载拉伸负荷测量塑料搭接接头剪切强度性能的测试方法。
ASTM D3330
Standard Test Method for Peel Adhesion of Pressure-Sensitive Tape
Standard test method for peel adhesion of pressure-sensitive tape.
ASTM D3330
压敏带材胶粘剂剥离的标准测试方法
压敏带材胶粘剂剥离的标准测试方法。
ASTM D3424
Standard Practice for Evaluating the Relative Lightfastness and Weatherability of Printed Matter
This standard describes procedures for the determination of the relative lightfastness and weatherability of printed matter under the following conditions, which involve exposure to natural daylight or accelerated procedures in the laboratory.
ASTM D3424
印刷品相对日晒色牢度和耐候性评估的标准测试方法
这个标准描述了印刷品在下列情况下相对日晒色牢度和耐候性的评估程序，涉及自然光曝露测试程序或实验室加速曝露测试程序。
ASTM D3451
Standard Guide for Testing Coating Powders and Powder Coatings
This guide covers the selection and use of procedures for testing coating powders and powder coatings. The test methods included are listed in Table 1. Where more than one test method is listed for the same characteristic, no attempt is made to indicate superiority of one method over another. Selection of the methods to be followed must be governed by experience and the requirements in each individual case, together with agreement between the purchaser and the seller.
ASTM D3451
涂料粉末和粉末涂料测试的标准指南
本指南规定了涂料粉末和粉末涂料测试的选择和使用程序。 测试方法已列于其中Table 1。对于某一特征，如果列出一个以上的测试方法，说明方法之间没有哪个更适合。 必须根据经验和每个案例的要求，以及买方和卖方之间的协议选择要遵循的方法。
ASTM D3528
Standard Test Method for Strength Properties of Double Lap Shear Adhesive Joints by Tension Loading
This test method covers the determination of the tensile shear strengths of adhesives for bonding metals when tested in an essentially peel-free standard specimen that develops adhesive stress distribution representative of that developed in a typical low-peel production-type structural joint.
ASTM D3528
通过加载拉伸负荷测量双搭接剪切粘结接头强度性能的标准测试方法
本测试方法规定了胶粘剂金属粘接的拉伸剪切强度的测定，该基于在无剥离标准件上进行，得到的胶粘剂应力分布代表了典型的低剥离产品类结构件上的情况。
ASTM D4101
Standard Specification for Polypropylene Injection and Extrusion Materials
This specification covers polypropylene materials suitable for injection molding and extrusion. Polymers consist of homopolymer, copolymers, and elastomer compounded with or without the addition of impact modifiers (ethylene-propylene rubber, polyisobutylene rubber, and butyl rubber), colorants, stabilizers, lubricants, or reinforcements.
ASTM D4101
聚丙烯注塑和挤出材料的标准规范
本规范规定了聚丙烯材料的注塑成型和挤出。 聚合物包括均聚物、共聚物及复合弹性体（加或不加聚异丁烯橡胶、乙丙橡胶、丁基橡胶等冲击改性剂），还有色素、稳定剂、润滑剂或增强剂。
ASTM D412
Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers - Tension
These test methods cover procedures used to evaluate the tensile (tension) properties of vulcanized thermoset rubbers and thermoplastic elastomers.
ASTM D412
硫化橡胶和热塑性弹性体张力的标准测试方法
这些测试方法描述了用来评估硫化橡胶和热塑性弹性体拉伸（张力）性能的程序。
ASTM D4214
Standard Test Methods for Evaluating the Degree of Chalking of Exterior Paint Films
These test methods cover the evaluation of the degree of chalking on white or tinted exterior paint films.
ASTM D4214
外墙涂料膜粉化程度评估的标准测试方法
本测试方法规定了白色或浅色外墙涂料膜粉化程度的评价
ASTM D4303
Standard Test Methods for Lightfastness of Colorants Used in Artists' Materials
Four test methods to accelerate the effects of long term indoor illumination on artists' materials are described.
ASTM D4303
艺术材料中使用的着色剂光稳定性的标准测试方法
描述了4种加速长期室内照明对艺术材料的影响的测试方法。
ASTM D4329
Standard Practice for Fluorescent UV Exposure of Plastics
This practice covers specific procedures and test conditions that are applicable for fluorescent UV exposure of plastics conducted in accordance with Practices G151 and G154.
ASTM D4329
塑料荧光紫外线暴露测试的标准测试方法
本测试方法规定了依照G151和G154测试方法对塑料进行荧光紫外线暴露测试的具体程序和测试条件。
ASTM D4355
Standard Test Method for Deterioration of Geotextiles by Exposure to Light, Moisture and Heat in a Xenon Arc Type Apparatus
This test method covers the determination of the deterioration in tensile strength of geotextiles by exposure to xenon arc radiation, moisture, and heat.
ASTM D4355
曝露在氙灯设备的光、潮湿和热中的土工布老化的标准测试方法
该测试方法规定了曝露在氙灯辐射、湿气和热量中的土工布拉伸强度退化的测定。
ASTM D4434
Standard Specification for Poly(Vinyl Chloride) Sheet Roofing
This specification covers flexible sheet made from poly(vinyl chloride) resin as the primary polymer intended for use in single-ply roofing membranes exposed to the weather.
ASTM D4434
聚氯乙烯屋面薄板的标准规范
本规范规定了拟用于单层屋顶薄膜的、用聚氯乙烯树脂作为初级聚合物而制造的柔性薄板空气暴露测试程序。
ASTM D4459
Standard Practice for Xenon-Arc Exposure of Plastics Intended for Indoor Applications
This practice covers specific procedures and test conditions that are applicable for exposure of plastics in window glass-filtered xenon-arc devices in accordance with Practices G151 and G155 for evaluating the stability of plastics intended for use in indoor applications.
ASTM D4459
室内用塑料氙灯曝露测试的标准测试方法
本测试方法规定了依照测试方法G151和G155，用配备窗玻璃滤光器的氙灯设备对塑料进行暴露测试的具体程序和测试条件，以评估室内用塑料的稳定性。
ASTM D4585
Standard Practice for Testing Water Resistance of Coatings Using Controlled Condensation
This practice covers basic principles and operating procedures for testing water resistance of coatings using controlled condensation.
ASTM D4585
使用可控的冷凝装置测试涂层耐水性的标准测试方法
本测试方法规定了可控冷凝设备测试涂层耐水性的基本原则和操作程序。
ASTM D4587
Standard Practice for Fluorescent UV-Condensation Exposures of Paint and Related Coatings
This practice covers the selection of test conditions for accelerated exposure testing of coatings and related products in fluorescent UV and condensation devices conducted according to Practices G151 and G154.
ASTM D4587
油漆及相关涂料荧光紫外线曝露测试的标准测试方法
本测试方法规定了油漆及相关涂料在荧光紫外线和冷凝装置中根据G151 和 G154测试方法进行加速曝露测试时对测试条件的选择
ASTM D4637
Standard Specification for EPDM Sheet Used In Single-Ply Roof Membrane
This specification covers flexible sheet made from ethylene-propylene-diene terpolymer (EPDM) intended for use in single-ply roofing membranes exposed to the weather.
ASTM D4637
用于单层屋顶薄膜的EPDM薄板的标准规范
本规范规定了拟用于单层屋顶薄膜的用乙烯丙烯三元共聚物（EPDM）制造的柔性薄板在空气中的曝露测试程序。
ASTM D4674
Standard Practice for Accelerated Testing for Color Stability of Plastics Exposed to Indoor Office Environments
This practice covers the basic principles and operating procedures for using fluorescent light to determine color stability of plastics when materials are exposed in typical office environments where fluorescent overhead lighting and window-filtered daylight are used for illumination and where temperature and humidity conditions are in accordance with American Society of Heating, Refrigerating, and Air-conditioning Engineers (ASHRAE) recommendations for workers' comfort.
ASTM D4674
曝露在室内办公环境的塑料色牢度加速测试的标准测试方法
本测试方法规定了使用荧光灯测定塑料光稳定性的基本原则和操作程序，材料曝露在典型的办公室环境下，头顶上的荧光和透射过窗玻璃的日光用于照明，环境的温度和湿度条件是根据美国供暖、制冷、空调工程师协会（ASHRAE）所提出的让职员感到舒适的建议而设定的。
ASTM D4798
Standard Practice for Accelerated Weathering Test Conditions and Procedures for Bituminous Materials (Xenon-Arc Method)
This practice covers test conditions and procedures for xenon-arc exposures according to Practices G151 and G155 for bituminous roofing and waterproofing materials.
ASTM D4798
沥青材料（氙弧法）加速老化测试条件和测试程序的标准测试方法
本测试方法规定了根据G151和G155沥青屋面和防水材料的做法进行氙灯曝露测试的测试条件和程序。
ASTM D4799
Standard Practice for Accelerated Weathering Test Conditions and Procedures for Bituminous Materials (Fluorescent UV, Water Spray, and Condensation Method)
This practice describes test conditions and procedures for fluorescent UV and condensation exposures conducted according to Practices G151 and G154 for bituminous roofing and waterproofing materials that have a minimum softening point of approximately 95°C (200°F) as determined by Test Method D36.
ASTM D4799
沥青材料（荧光紫外线、喷淋及冷凝法）加速老化测试条件和测试程序的标准测试方法
本测试方法描述了根据G151和G154沥青屋面和防水材料(最低软化点约950) 的做法进行荧光紫外线和冷凝曝露测试的测试条件和程序。
ASTM D4811
Standard Specification for Nonvulcanized (Uncured) Rubber Sheet Used as Roof Flashing
This specification covers nonvulcanized (uncured) rubber sheet made of EPDM (ethylene-propylene-diene terpolymer) or CR (polychloroprene) intended for use as watertight roof flashing exposed to the weather.
ASTM D4811
用作屋面防雨板的非硫化（未固化）橡胶薄板的标准规范
本规范规定了由EPDM（乙烯丙烯三元共聚物）或CR（氯丁橡胶）制成的、拟用于防水屋面防雨板的非硫化（未固化）橡胶薄板在空气中的曝露测试。
ASTM D5010
Standard Guide for Testing Printing Inks and Related Materials
This guide covers a list of test methods, practices, and specifications that can be used for the testing and evaluation of printing inks, printed ink films, and substrates used in their production.
ASTM D5010
印刷油墨和相关材料测试标准指南
本指南规定了测试方法、实施规程和规格的列表，可用于测试和评价印刷油墨、油墨印刷胶片和产品用底板。
ASTM D5019
Standard Specification for Reinforced CSM (Chlorosulfonated Polyethylene) Sheet Used in Single-Ply Roof Membrane
This specification covers reinforced non-vulcanized polymeric sheet made from chlorosulfonated polyethylene (CSM) intended for use as a single-ply roof membrane exposed to the weather.
ASTM D5019
用于单层屋顶薄膜的增强CSM板（氯磺化聚乙烯）的标准规范
本规范规定了拟用于单层屋顶薄膜的、用氯磺化聚乙烯（CSM）制造的增强非硫化聚合物板空气曝露测试程序。
ASTM D5034
Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test)
This test method covers the grab and modified grab test procedures for determining the breaking strength and elongation of most textile fabrics.
ASTM D5034
纺织面料断裂强度和伸长率（抓样法）的标准测试方法
本测试方法规定了测定绝大多数纺织面料的断裂强度和断裂伸长率的抓样法和修改的抓样法的测试程序。
ASTM D5035
Standard Test Method for Breaking Force and Elongation of Textile Fabrics (Strip Method)
This test method covers raveled strip and cut strip test procedures for determining the breaking force and elongation of most textile fabrics.
ASTM D5035
纺织面料断裂强度和伸长率（条样法）的标准测试方法
本测试方法规定了测定绝大多数纺织面料的断裂强度和伸长率的条样法的测试程序。
ASTM D5071
Standard Practice for Exposure of Photodegradable Plastics in a Xenon Arc Apparatus
This practice covers specific procedures and test conditions that are applicable for xenon arc exposure of photodegradable plastics conducted in accordance with Practices G151 and G155.
ASTM D5071
氙灯装置中光降解塑料曝露测试的标准测试方法
本测试方法规定了依照G151和G155测试方法对塑料进行光降解氙灯曝露测试的具体程序和测试条件。
ASTM D5208
Standard Practice for Fluorescent Ultraviolet (UV) Exposure of Photodegradable Plastics
This practice covers the specific procedures applicable for fluorescent Ultraviolet (UV) exposure of photodegradable plastics conducted in accordance with Practices G151 and G154.
ASTM D5208
光降解塑料荧光紫外线 (UV) 曝露测试的标准测试方法
本测试方法规定了依照G151和G154测试方法对塑料进行光降解荧光紫外线 (UV)曝露测试的具体程序和测试条件。
ASTM D523
Standard Test Method for Specular Gloss
This test method covers the measurement of the specular gloss of nonmetallic specimens for glossmeter geometries of 60, 20, and 85°.
ASTM D523
光泽的标准测试方法
本测试方法规定了光泽计在60、20、和85度时非金属样品光泽度的测量；
ASTM D5383
Standard Practice for Visual Determination of the Lightfastness of Art Materials by Art Technologists
This practice covers a method for exposing specimens of colored art materials indoors to sunlight coming through a closed window.
ASTM D5383
艺术材料日晒色牢度目测标准测试方法
本测试方法规定了室内彩色艺术材料样品曝露于透过封闭窗玻璃的太阳光中的测试。
ASTM D5398
Standard Practice for Visual Evaluation of the Lightfastness of Art Materials by the User
This practice covers a method for exposing specimens of colored art materials indoors to sunlight coming through a closed window.
ASTM D5398
用户对艺术材料日晒色牢度目测评估的测试方法
本测试方法规定了室内彩色艺术材料样品曝露于透过封闭窗玻璃的太阳光中的测试。
ASTM D5819
Standard Guide for Selecting Test Methods for Experimental Evaluation of Geosynthetic Durability
This guide covers a designer/specifier through a systematic determination of those factors of the appropriate application environment that may affect the post-construction service life of a geosynthetic.
ASTM D5819
土工合成材料耐候性测试评估方法选择的标准指南
本指南系统地设计/明确了可能影响土工合成材料施工后的使用寿命的环境因素。
ASTM D5894
Standard Practice for Cyclic Salt Fog/UV Exposure of Painted Metal, (Alternating Exposures in a Fog/Dry Cabinet and a UV/Condensation Cabinet)
This practice covers basic principles and operating practice for cyclic corrosion/UV exposure of paints on metal; using alternating periods of exposure in two different cabinets: a cycling salt fog/dry cabinet, and a fluorescent UV/condensation cabinet.
ASTM D5894
涂层金属的循环盐雾/紫外线暴露试验（交替暴露在盐雾/干燥装置和紫外线/冷凝装置中）的标准测试方法
本测试方法规定了金属上涂层循环腐蚀/紫外线暴露测试的基本原则和操作程序；在两个不同试验箱之间进行交替暴露： 一个是盐雾/干燥循环，一个是荧光紫外线/冷凝循环。
ASTM D6083
Standard Specification for Liquid Applied Acrylic Coating Used in Roofing
This specification covers liquid-applied water-dispersed acrylic latex elastomeric protective roof coatings.
ASTM D6083
屋顶用液态丙烯酸涂料标准规范
本规范描述了液态水分散型丙烯酸乳液橡胶屋顶防护涂料。
ASTM D624
Standard Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers
This test method describes procedures for measuring a property of conventional vulcanized rubber and thermoplastic elastomers called tear strength.
ASTM D624
常规硫化橡胶和热塑性弹性体撕裂强度的标准测试方法
本测试方法描述了测量常规硫化橡胶和热塑性弹性体（称为撕裂强度）的性能的程序。
ASTM D638
Standard Test Method for Tensile Properties of Plastics
This test method covers the determination of the tensile properties of unreinforced and reinforced plastics in the form of standard dumbbell-shaped test specimens when tested under defined conditions of pretreatment, temperature, humidity, and testing machine speed.
ASTM D638
塑料拉伸性能的标准测试方法
本测试方法规定了非增强和增强塑料拉伸性能的测定，测试样品为标准哑铃形，在限定的预处理、温度、湿度和测试机速度条件下进行测试。
ASTM D6551
Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Xenon-Arc Exposure Apparatus
This practice describes one environment for the exposure of pressure-sensitive tape, used primarily for packaging, to a laboratory accelerated weathering environment.
ASTM D6551
使用氙灯曝露装置对与压力敏感的带材进行加速老化的标准测试方法
本测试方法描述了实验室加速老化环境下对与压力敏感的带材进行曝露测试，主要用于包装材料。
ASTM D6551
使用氙灯曝露装置对与压力敏感的带材进行加速老化的标准测试方法
本测试方法描述了实验室加速老化环境下对与压力敏感的带材进行曝露测试的程序，主要用于包装材料。
ASTM D6577
Standard Guide for Testing Industrial Protective Coatings
This guide covers the selection and use of test methods and procedures for testing industrial protective coatings.
ASTM D6577
工业防护涂料测试标准指南
本指南规定了工业防护涂料测试方法和测试程序的选择和使用。
ASTM D660
Standard Test Method for Evaluating Degree of Checking of Exterior Paints
Since checking is not easily recognizable, this test method is intended to provide, through definition and illustrations, a means of evaluating the degree of this film failure.
ASTM D660
外墙涂料粉化程度评估的标准测试方法
由于粉化不容易辨认，此测试方法旨在通过定义和插图提供该薄膜失效程度的评估。
ASTM D661
Standard Test Method for Evaluating Degree of Cracking of Exterior Paints
This test method covers the evaluation of the degree of cracking of exterior paints by comparison with photographic standards.
ASTM D661
外墙涂料开裂程度评估的标准测试方法
本测试方法规定了与影像标准比较评估外墙涂料开裂程度的办法。
ASTM D662
Standard Test Method for Evaluating Degree of Erosion of Exterior Paints
This test method covers the evaluation of the degree of erosion of exterior paints by comparison with photographic standards.
ASTM D662
外墙涂料腐蚀程度评估的标准测试方法
本测试方法规定了与影像标准比较评估外墙涂料腐蚀程度的办法。
ASTM D6675
Standard Practice for Salt-Accelerated Outdoor Cosmetic Corrosion Testing of Organic Coatings on Automotive Sheet Steel
This practice is designed to assist procedures to be followed when conducting outdoor exposures to evaluate cosmetic corrosion that might occur in steel panels covered with an organic coating that has been damaged.
ASTM D6675
汽车钢板有机涂层的盐加速户外装饰品腐蚀测试的标准测试方法
本测试方法的目的是，当进行户外曝露测试以评估可能发生在所覆盖的有机涂层已损坏的钢板上的装饰品腐蚀时，协助应遵循的程序。
ASTM D6695
Standard Practice for Xenon-Arc Exposures of Paint and Related Coatings
This practice covers the selection of test conditions for accelerated exposure testing of coatings and related products in xenon arc devices conducted according to Practices G151 and G155.
ASTM D6695
油漆及相关涂料氙灯曝露测试的标准测试方法
本测试方法规定了涂料及相关产品在氙灯设备中根据G151 和 G155测试方法进行加速曝露测试时对测试条件的选择。
ASTM D6862
Standard Test Method for 90 Degree Peel Resistance of Adhesives
This test method covers the determination of the resistance-to-peel strength of an adhesive bond between one rigid adherend and one flexible adherend when tested at an angle of approximately 90 degrees under specified conditions of preparation and testing.
ASTM D6862
胶粘剂抗90度剥离的标准测试方法
本测试方法规定了刚性粘合体和柔性粘合体之间的胶粘剂接头的抗剥落强度的测定，测试时的角度约90度，在特定的制备与测试条件下进行。
ASTM D6878
Standard Specification for Thermoplastic Polyolefin Based Sheet Roofing
This specification covers flexible sheet made from thermoplastic polyolefin (TPO) as the principal polymer, intended for use in single-ply roofing membranes exposed to the weather.
ASTM D6878
基于热塑性聚烯烃的屋顶板标准规范
本规范规定了拟用于单层屋顶薄膜的、用热塑性聚烯烃（TPO）作为主要聚合物而制造的柔性板空气暴露测试程序。
ASTM D7003
Standard Test Method for Strip Tensile Properties of Reinforced Geomembranes
This test method is used to measure the strip tensile properties of reinforced geomembranes.
ASTM D7003
增强土工薄膜条样拉伸性能的标准测试方法
本测试方法用于测量增强土工薄膜条样拉伸性能。
ASTM D7004
Standard Test Method for Grab Tensile Properties of Reinforced Geomembranes
This test method is used to measure the grab tensile properties of reinforced geomembranes.
ASTM D7004
增强土工薄膜抓样拉伸性能的标准测试方法
本测试方法用于测量增强土工薄膜抓样拉伸性能。
ASTM D7087
Standard Test Method for An Imaging Technique to Measure Rust Creepage at Scribe on Coated Test Panels Subjected to Corrosive Environments
This test method covers the measurement of rust creepage area from a scribe line on painted/coated flat test panels after exposure to corrosive environments.
ASTM D7087
用成像技术测量在腐蚀环境中涂覆测试板划痕处锈蚀蠕变的标准测试方法
本测试方法规定了暴露于腐蚀环境后，从油漆/涂层平面试板划痕处开始的锈蚀蠕变区域的测量。
ASTM D714
Standard Test Method for Evaluating Degree of Blistering of Paints
This test method employs photographic reference standards to evaluate the degree of blistering that may develop when paint systems are subjected to conditions which will cause blistering.
ASTM D714
涂料起泡程度评估的标准测试方法
本测试方法采用影像参考标准评价起泡程度，当油漆系统处于会导致起泡的条件下时起泡可能会扩展。
ASTM D7356
Standard Test Method for Accelerated Acid Etch Weathering of Automotive Clearcoats Using a Xenon-Arc Exposure Device
This test method covers an accelerated exposure test intended to simulate defects in automotive clearcoats caused by acid rain that occurs at the Jacksonville, Florida exposure site.
ASTM D7356
使用氙灯暴露设备对汽车面漆进行加速酸蚀老化的标准测试方法
本测试方法旨在模拟发生在佛罗里达曝晒场杰克逊维尔的因酸雨造成的汽车清漆破坏的加速暴露测试。
ASTM D750
Standard Test Method for Rubber Deterioration Using Artificial Weathering Apparatus
This test method covers specific variations in the test conditions and procedures that shall be applicable when Practice G151 plus either Practice G152, G153, G154, or G155 are employed for exposure of vulcanized rubber compounds.
ASTM D750
使用人工老化设备对橡胶进行老化试验的标准测试方法
本测试方法规定了可用的测试条件和测试程序的具体变化，在进行硫化橡胶复合物曝露测试时，可采用测试方法G151和G152、G153、G154、G155中的任意一个。
ASTM D751
Standard Test Methods for Coated Fabrics
These test methods cover, but are not limited to, rubber-coated fabrics; that is, tarpaulins, rainwear, and similar products
ASTM D751
涂层织物的标准测试方法
本测试方法包括但不限于橡胶涂层织物，即防水油布、雨衣及类似产品
ASTM D772
Standard Test Method for Evaluating Degree of Flaking (Scaling) of Exterior Paints
This test method covers the evaluation of the degree of flaking (scaling) of exterior paints by comparison with photographic standards.
ASTM D772
外墙涂料剥落（起皮）程度评估的标准测试方法
本测试方法规定了用影像标准比较法评估外墙涂料剥落（起皮）程度的办法。
ASTM D882
Standard Test Method for Tensile Properties of Thin Plastic Sheeting
This test method covers the determination of tensile properties of plastics in the form of thin sheeting and films (less than 1.0 mm (0.04 in.) in thickness).
ASTM D882
薄塑料板拉伸性能的标准测试方法
本测试方法规定了薄片和薄膜（小于1毫米（0.04英寸）厚度）塑料拉伸性能的测定。
ASTM D904
Standard Practice for Exposure of Adhesive Specimens to Artificial Light
This practice covers the basic principles and operating procedures for ultraviolet (UV) light aging (with or without water) of adhesive bonded joints having at least one glass or transparent adhered, using fluorescent UV (see Method A) or xenon-arc light sources (see Method B).
ASTM D904
人工光源胶粘剂样品暴露的标准测试方法
本测试方法规定了胶接接头（至少有一个玻璃或透明粘接）紫外线（UV）光老化（有水循环或无水循环）的基本原则和操作程序，使用荧光紫外线（见方法A）或氙弧光源（见方法B）。
ASTM D925
Standard Test Methods for Rubber Property—Staining of Surfaces (Contact, Migration, and Diffusion)
These test methods cover techniques to evaluate three types of staining that rubber may cause when in contact with, or in proximity to, another surface that may be light colored.
ASTM D925
橡胶性能——表面染色（接触、迁移、扩散）的标准测试方法
这些测试方法规定了评估橡胶材料接触或靠近其他浅色表面产生的三种沾色的技术。
ASTM F1164
Standard Test Method for Evaluation of Transparent Plastics Exposed to Accelerated Weathering Combined with Biaxial Stress
This test method covers the resistance of transparent plastics exposed to environmental conditioning (accelerated weathering) under a biaxial stress state induced by a pressure cell/test fixture.
ASTM F1164
透明塑料受到双轴应力与加速老化暴露评估的标准测试方法
本测试方法规定了透明塑料在压力部件/测试支架导致的双轴应力状态下曝露于环境条件（加速老化）的抵抗力。
ASTM F1945
Standard Practice for Determining the Lightfastness of Ink Jet Prints Exposed to Indoor Fluorescent Lighting
This practice covers an accelerated procedure intended to determine the lightfastness of ink jet prints in office environments where overhead fluorescent light is used for illumination.
ASTM F1945
曝露在室内荧光灯下喷墨印刷品光稳定性测定的标准测试方法
本测试方法规定了旨在测定办公室环境下喷墨印刷品光稳定性的加速程序，该环境中用作照明的是头顶上的荧光灯。
ASTM F2366
Standard Practice for Determining the Relative Lightfastness of Ink Jet Prints Exposed to Window Filtered Daylight Using a Xenon Arc Light Apparatus
This practice covers specific procedures and test conditions that are applicable for xenon-arc exposure of ink jet media prints conducted in accordance with Practices G151 and G155.
ASTM F2366
使用配备窗玻璃滤光器的氙灯设备测试喷墨印刷品的相对光稳定性的标准测试方法
本测试方法规定了依照G151和G155测试方法对喷墨纸张印刷品进行氙灯曝露测试的具体程序和测试条件。
ASTM G151
Practice for Exposing Nonmetallic Materials in Accelerated Test Devices That Use Laboratory Light Sources
This practice provides general procedures to be used when exposing nonmetallic materials in accelerated test devices that use laboratory light sources.
ASTM G151
使用实验室光源加速测试设备对非金属材料进行曝露的测试方法
本测试方法提供了在实验室光源加速测试设备中对非金属材料进行曝露测试的一般程序。
ASTM G154
Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials
This practice covers the basic principles and operating procedures for using fluorescent UV light, and water apparatus intended to reproduce the weathering effects that occur when materials are exposed to sunlight (either direct or through window glass) and moisture as rain or dew in actual usage.
ASTM G154
使用荧光紫外线设备对非金属材料进行曝露的测试方法
本测试方法是使用荧光紫外灯和冷凝装置进行曝露测试的基本原则和操作程序，旨在再现材料曝露在阳光下（直接或透过窗玻璃）和曝露在湿气中（雨水或露水）发生的老化效果。
ASTM G155
Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials
This practice covers the basic principles and operating procedures for using xenon arc light and water apparatus intended to reproduce the weathering effects that occur when materials are exposed to sunlight (either direct or through window glass) and moisture as rain or dew in actual use.
ASTM G155
使用氙灯设备对非金属材料进行曝露的测试方法
本测试方法是使用氙灯和水喷淋装置进行曝露测试的基本原则和操作程序，旨在再现材料曝露在阳光下（直接或透过窗玻璃）和曝露在湿气中（雨水或露水）发生的老化效果。
ASTM G85
Standard Practice for Modified Salt Spray (Fog) Testing
This practice covers and sets forth conditions for five modifications in salt spray (fog) testing for specification purposes.
ASTM G85
改进的盐雾试验的标准测试方法
本测试方法包括并描述了5种盐雾测试方法的修改条件。
EN 13523-10 (DIN)
Coil Coated Metals - Test Methods Part 10: Resistance to Fluorescent UV Radiation and Water Condensation
EN 2591-320 (DIN)
Elements of Electrical and Optical Connection - Test Methods Part 320: Simulated Solar Radiation at Ground Level
Ford FLTM BI 103-01
Salt Spray Resistance Test for Painted Panels and Parts
This method is used to test the resistance to salt spray of painted panels and parts.
Ford FLTM BI 103-01
彩板及配件耐盐雾试验
本方法用于漆板和配件的耐盐雾测试。
Ford FLTM BI 104-01
Water Immersion Test for Painted Parts and Panels
This method is used to determine the resistance to failure of painted metal and painted plastic parts and representative test panels when immersed in water.
Ford FLTM BI 104-01
油漆部件和面板的水浸试验
本方法用于测定涂层金属、涂层塑料件和典型测试板在水中浸泡时的失效。
Ford FLTM BI 104-02
Condensing Water Vapor Test
This procedure is used to evaluate the effects of a condensing water atmosphere on treated panels.
Ford FLTM BI 104-02
冷凝水蒸气测试
本程序用来评估处理板上冷凝水环境的效果。
Ford FLTM BI 160-01
Florida and Arizona Outdoor Exposure Test
Ford FLTM BI 160-01
佛罗里达和亚利桑那的户外曝露测试
GB 5938
corrosion-resistant testing method of the metal deposits and conversion coatings for the light industrial products Neutral salt spraying test (NSS)
This standard applies to the inspection of the corrosion resistance of metal coatings and chemically treated layers.
GB 6806
Anodizing of aluminium and its alloys--Accelerated test of light fastness of coloured anodic oxide coatings using artificial light
This standard specifies the artificial light accelerated test method for evaluating the light resistance of aluminum and aluminum alloy colored anodized films.
GB/T 10125
Corrosion tests in artificial atmospheres-salt spray tests
This standard specifies the equipment, reagents and methods used for neutral salt spray (NSS), acetate salt spray (AASS), and copper-accelerated acetate salt spray (CASS) tests.
GB/T 16259
Test method for in accelerated weathering building materials
This standard specifies the content, test conditions, test procedures, test results, and test reports of artificial climate accelerated aging test devices using xenon lamps as the light source for building material products.
GB/T 16422.1
Plastics-Methods of the exposure to laboratory light sources Part 1:general guidance
This part of GB / T 16422 provides information and general principles on the selection and implementation of exposure methods described in detail in the following sections. It also describes and recommends methods for measuring irradiance and radiant quantities, and describes monitoring boxes. Equipment requirements for body air temperature and surface temperature of dark and light colored materials.
GB/T 16422.1
Plastics-Methods of the exposure to laboratory light sources Part 1:general guidance
This part of GB / T 16422 provides information and general principles on the selection and implementation of exposure methods described in detail in the following sections. It also describes and recommends methods for determining irradiance and radiation levels, and describes monitoring boxes Equipment requirements for body air temperature and surface temperature of dark and light colored materials.
GB/T 16422.2
Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc sources
This part of GB / T 16422 specifies the test method for plastic samples exposed to xenon arc lamps in the presence of moisture. This method is used to simulate the natural occurrence of materials in sunlight in the actual use environment after exposure to sunlight or filter glass Aging effect.
GB/T 16422.3
Plastics - Methods of exposure to laboratory light sources - Part 3: Fluorescent UV lamps
This part of GB / T 16422 specifies the test method for the exposure of test specimens in test equipment equipped with fluorescent ultraviolet radiation, heat and water. A natural aging effect that occurs under daylight.
GB/T 16991
Textiles - Test for colour fastness - Colour fastness and ageing to artificial light at high temperatures: Xenon arc
This standard specifies a method for determining the color of various types of textiles, the ability of artificial light sources to replace natural sunlight, the ability to resist heat, and the ability to resist aging. This test method specifically takes into account the effects of light and heat generated by the interior of the vehicle on the textile.
GB/T 1710
Comparison of resistance to light of coloured pigments of similar types
This standard specifies a general test method for the comparison of light fastness of the same type of pigments (agreed reference pigments and test samples).
GB/T 1771
Paints and varnishes-determination of resistance to neutral salt spray (fog)
This standard specifies the method for determining the resistance of coatings to neutral salt spray.
GB/T 18244
Test methods for resistance to weathering of building waterproofing materials
This standard specifies test methods for hot air aging, ozone aging, and artificial climate accelerated aging (xenon arc lamps, carbon arc lamps, ultraviolet fluorescent lamps).
GB/T 1865
Paints and varnishes - Artificial weathering and exposure to artificial radiation - Exposure to filtered xenon-arc radiation
This standard specifies artificial weathering test procedures for paints and varnishes exposed to xenon lamp devices and water and water vapor. The results of aging can be individually evaluated by comparing the parameters selected before, during and after aging.
GB/T 19394
UV test photovoltaic (PV) modules
This standard specifies tests for assessing the resistance to ultraviolet radiation of photovoltaic modules when exposed to ultraviolet radiation. This test is suitable for assessing the resistance to UV radiation of materials such as polymers and protective layers.
GB/T 20853
Corrosion of metals and alloys-Corrosion in artificial atmosphere-Accelerated corrosion test involving exposure under controlled conditions of humidity cycling and intermittent spraying of a salt solution
This standard specifies the test method for the corrosion resistance of metals in the presence of chloride ions. Chloride ions are mainly sodium chloride from marine and highway deicing salts.
GB/T 20854
Corrosion of metals and alloys-Accelerated testing involving cyclic exposure to salt mist, "dry" and "wet" condition
This standard specifies the instruments and test methods for accelerated corrosion tests used to evaluate the corrosion resistance of metal materials used in outdoor salt-contaminated environments, regardless of whether the material being tested has permanent or temporary corrosion protection. This standard specifies the conditions for cyclic exposure of samples to neutral salt spray, "dry" and "wet" test environments.
GB/T 22771
Graphic techmology-Prints and printing inks-Assessment of light fastness using filtered xenon arc light
This standard specifies a method for determining the light resistance of printed matter and printing inks. It gives two test conditions: basic test conditions for printed matter and special test conditions for ink.
GB/T 23983
Test method for yellowing resistance of wood coatings
This standard specifies the test method for the determination of yellowing resistance of single-layer or multi-layer coatings of wood coatings using fluorescent ultraviolet aging equipment.
GB/T 23987
Paints and varnishes - Exposure of coatings to artificial weathering - Exposure to fluorescent UV lamps and water
This standard specifies test methods for determining the weathering resistance of coatings using test equipment containing fluorescent UV lamps and condensation or water spray.
GB/T 2423.24
Environmental testing for electric and electronic products Part 2:Test methods-Test Sa: simulated solar radiation at ground level
This standard is used to test the impact of ground solar radiation on equipment and components (thermal, mechanical, chemical, electrical, etc.)
GB/T 29365
Wood-plastic composite (WPC) – test methods of artificial weathering
This standard specifies the artificial weathering test method for plastic-wood composite materials.
GB/T 30669
Textiles - Tests colour fastness - Colour fastness to light yellowing
This standard specifies the test method for the light yellow fastness of textile materials exposed to ultraviolet light.
GB/T 31881
Accelerated weathering test methods of automotive nonmetal components and materials using a fluorescent UV and condendation apparatus
This standard specifies the test methods and evaluation methods for accelerated aging of automotive non-metal parts and materials using ultraviolet aging test equipment.
GB/T 31899
Textile - Tests for weather resistance - UV light exposure
This standard specifies the test method for UV exposure and aging of outdoor textiles and the determination of the change in properties before and after aging.
GB/T 32088
Accelerated weathering test methods of automotive nonmetal components and materials using a xenon-arc apparatus
This standard specifies the test method and evaluation method for accelerating aging of automotive non-metal parts and materials using controlled irradiance xenon equipment.
GB/T 8427
Textiles-Tests for colour fastness-Colour fastness to artifical light:Xenon arc fading lamp test
This standard specifies a method to determine the color fastness of various types of textiles to the artificial light effect equivalent to sunlight (D65). This standard can also be used for white (bleached or fluorescent whitened) textiles.
GM 4298P
Salt Spray Test
GM 4298P
盐雾测试
GM 4465P
Water Fog Humidity Test
This standard covers the requirements for testing water resistance of coated specimens in saturated water fog conditions.
GM 4465P
水雾湿度测试
本标准规定了涂层样品在饱和水雾条件下进行耐水性测试的要求。
GM 9125P
Procedures for Laboratory Accelerated Exposure of Automotive Materials
These procedures are used to determine the resistance to degradation of automotive materials when subjected to artificial light sources. It describes exposures to sunshine carbon arc, xenon arc, fluorescent ultraviolet light and condensation apparatus, and a twin carbon arc.
GM 9125P
汽车材料实验室加速老化测试程序
这些程序用于测定受到人造光源照射时汽车材料的抗降解能力。 它描述了日光型碳弧、氙弧、荧光紫外线和冷凝装置和双碳弧的暴露测试。
IEC 61215
Crystalline Silicon Terrestrial Photovaltalic (PV) Modules - Design Qualification and Type Approval
IEC 61215
地面用晶体硅光伏组件（PV）－设计鉴定和定型
IEC 61345
UV Test for Photovaltalic (PV) Modules
IEC 61345
光伏组件（PV）紫外试验
ISO 105-B02 (EN) (DIN)
Textiles-Tests for colour fastness- Part B02: Colour fastness to artificial light: Xenon arc fading lamp test
ISO 105-B02 (EN) (DIN)
纺织品-日晒色牢度试验-B02部分：人造光色牢度： 氙弧灯
ISO 105-B04 (EN) (DIN)
Textiles - Tests for Colour Fastness - Part B04. Colour Fastness to Artificial Weathering: Xenon Arc Fading Lamp Test
ISO 105-B06 (EN) (DIN)
Textiles - Tests for Colour Fastness - Part B06: Colour Fastness and Ageing to Artificial Light at High Temperatures: Xenon Arc Fading Lamp Test
ISO 105-B07 (EN) (DIN)
Textiles - Tests for Colour Fastness - Part B07: Colour Fastness to Light of Textiles Wetted with Artificial Perspiration
ISO 105-B10 (EN) (DIN)
Textiles - Tests for Colour Fastness - Part B10: Artificial Weathering - Exposure to Filtered Xenon-Arc Radiation
ISO 11341 (EN) (DIN)
Paints and Varnishes - Artificial weathering and exposure to artificial radiation- Exposure to filtered xenon-arc radiation
ISO 11341 (EN) (DIN)
色漆和清漆 –人工老化和人工辐射曝露测试-曝露于过滤的氙弧灯辐射
ISO 11507 (EN) (DIN)
Paints and Varnishes - Exposure of coatings to artificial weathering- Exposure to fluorescent UV lamps and water
This International Standard specifies exposure conditions for paint coatings exposed to artificial weathering in apparatus including fluorescent UV lamps and condensation or water spray.
ISO 11507 (EN) (DIN)
色漆和清漆 – 涂料的人工老化曝露测试–曝露于荧光紫外线灯管和水
本国际标准规定了油漆涂层曝露于人工老化装置（包括荧光紫外线灯管和冷凝或喷水）的暴露测试条件。
ISO 12040
Graphic Technology - Prints and Printing Inks - Assessment of Light Fastness Using Filtered Xenon Arc Light
ISO 12040
图形技术-印刷品和印刷油墨-用过滤氙弧灯评估光稳定性
ISO 29664
Plastics - Artificial weathering including acidic deposition
ISO 4582
Plastics — Determination of changes in colour and variations in properties after exposure to daylight under glass, natural weathering or laboratory light sources
This International Standard describes procedures used to determine changes in color and other appearance properties, and variations in mechanical or other properties, of plastics that have been exposed to daylight behind glass, to natural weathering or to light from a laboratory source.
ISO 4582
塑料-曝露于玻璃下日光、自然老化或实验室光源后颜色和性能变化的测定
本国际标准描述了用于测定塑料经玻璃下日光、自然老化或实验室光源曝露后性能变化的程序，包括塑料颜色和其他外观属性变化、机械或其他性能变化。
ISO 4892-1 (EN) (DIN)
Plastics – Methods of Exposure to Laboratory Light Sources – Part 1: General guidance
ISO 4892-1 (EN) (DIN)
塑料–使用实验室光源进行曝露测试的方法–第一部分 一般指导
ISO 4892-2 (EN) (DIN)
Plastics - Methods of Exposure to Laboratory Light Sources - Part 2: Xenon-arc lamps
ISO 4892-2 (EN) (DIN)
塑料–使用实验室光源进行曝露测试的方法–第二部分 氙弧灯
ISO 4892-3 (EN) (DIN)
Plastics - Methods of Exposure to Laboratory Light Sources - Part 3: Fluorescent UV Lamps
ISO 4892-3 (EN) (DIN)
塑料–使用实验室光源进行曝露测试的方法–第三部分 荧光紫外灯
ISO 527
Plastics - Determination of Tensile Properties
ISO 527
塑料-拉伸性能的测定
ISO 7253
Paints and Varnishes- Determination of resistance to neutral salt spray (fog)
This International Standard is one of a series of standards dealing with the sampling and testing of paints, varnishes and related products.
ISO 7253
色漆和清漆-耐中性盐雾的测定
本国际标准是处理色漆、清漆和相关产品采样和测试的一系列的标准之一。
ISO 877-1 (EN) (DIN)
Plastics - Methods of Exposure to Solar Radiation - Part 1: General Guidance
ISO 877-1 (EN) (DIN)
塑料–太阳辐射曝露方法–第一部分 一般指导
ISO 9227
Corrosion Tests in Artificial Atmospheres - Salt Spray Tests
ISO 9227
人造环境中的腐蚀测试-盐雾测试
LP463-KB19-01
Outdoor Exposure of Trim Materials
LP463-KB19-01
装饰材料的户外曝露
LP463-PB34-01
Florida Exposure Testing of Painted Surfaces
LP463-PB34-01
油漆表面佛罗里达测试
QB/T 2727
Leather-Tests for colour fastness-colour fastness to artificial light: Xenon arc
This standard specifies the test method for the color of leather against artificial light sources and heat resistance.
QB/T 4873
Test methods of artificial leather and synthetic leather - Exposure to laboratory light sources
This standard specifies three methods for the light source exposure test of artificial leather and synthetic leather laboratories: xenon arc lamp method (A method), fluorescent ultraviolet lamp method (B method), and open carbon arc lamp method (C method), and their results and Evaluation.
SAE J1523
Metal to Metal Overlap Shear Strength Test for Automotive Type Adhesives, Recommended Practice
This SAE Recommended Practice defines a procedure for determining shear strengths of adhesives.
SAE J1523
汽车用胶粘剂金属和金属间的剪切强度测试，推荐做法
本SAE标准定义了测定胶粘剂剪切强度的程序。
SAE J1959
Corrosion Preventive Compound, Underbody Vehicle Corrosion Protection
SAE J1959
防腐材料，车辆车底腐蚀防护
SAE J2020
Accelerated Exposure of Automotive Exterior Materials Using a Fluorescent UV and Condensation Apparatus
SAE J2020
使用荧光紫外线和冷凝装置对汽车外部材料进行加速曝露测试
SAE J2412
使用可控辐照度的氙灯设备对汽车内饰件进行加速曝露测试
该测试方法描述了受控辐照度的氙灯装置用于各种汽车内饰件加速曝露测试的操作程序
SAE J2412
Accelerated Exposure of Automotive Interior Trim Components Using a Controlled Irradiance Xenon-Arc Apparatus
This test method specifies the operating procedures for a controlled irradiance, xenon arc apparatus used for the accelerated exposure of various automotive interior trim components.
SAE J2527
Performance Based Standard for Accelerated Exposure of Automotive Exterior Materials Using A Controlled Irradiance Xenon-Arc Apparatus
This SAE Standard specifies the operating procedures for a controlled irradiance, xenon-arc apparatus used for the accelerated exposure of various exterior automotive materials.
SAE J2527
使用可控辐照度的氙灯设备对汽车外饰材料进行加速曝露的测试标准
本SAE标准描述了受控辐照度的氙灯装置用于各种汽车外饰材料加速曝露测试的操作程序。
T/CSAE 71
Cyclic corrosion test methods of automotive assemblies and materials
This standard specifies the cyclic corrosion test methods for automotive parts and materials.
VW PV 1306
Exposure Test for Determining the Tackiness of Polypropylene Parts
VW PV 1306
测定聚丙烯零件粘性的曝露测试
VW PV 3929
Non-Metallic Materials, Weathering in Dry, Hot Climate
VW PV 3929
非金属材料在干、热气候环境中的老化
VW PV 3930
Non-Metallic Materials, Weathering in Moist, Hot Climate
VW PV 3930
非金属材料在湿、热气候环境中的老化
YY/T 0631
dental materials - determination of color stability
This standard specifies the method for determining the color stability of dental materials after immersion in light.
Looking for a specific test standard? Search entire listing of all standards.
您现已登陆账户。您可以阅读所有标(
) 或 (
) 文件。想要阅读标 (
) 文件， 请注册您的设备.
您现已登陆账户。您可以阅读所有标() 或 () 文件。想要阅读标 () 文件， 请注册您的设备.